No. 4 1/2 Smooth Plane

Price: $325.00
Product ID : 1-4-1-2

Purchase

E-mail to a friend | Add To Wish List

Details

No. 4 1/2 Smooth Plane

Solidly built, this is the ultimate smoothing plane. It is longer, wider, and heavier than the No. 4, and its extra thick blade eliminates the possibility of chatter.

  • 10-3/8" long. Blade is 2-3/8" wide x .140" thick.
  • Iron body only, 5-1/2 lbs.

Use

Bench Planes

Lie-Nielsen Bench Planes (except for the No. 1) are based on the Stanley Bedrock-type planes. Bedrocks were Stanley’s top line of Bench Planes, heavier and better made than the standard. In addition, the construction of the frog is unique — it features a fully machined fit between frog and body, adjustable from the rear without having to remove the blade and cap. This allows you to easily change the mouth setting from a coarse to fine cut for difficult woods or fine smoothing passes.

Geometry:

All Bench Plane blades are bedded at 45° with the bevel down.

Blade Sharpening:

Your Lie-Nielsen Bench Plane is ready to cut wood out of the box. The blade is ground sharp at a 25° bevel. A secondary bevel of up to 5 degrees helps achieve a razor edge quickly. This also improves edge life in hardwoods. For more information on advanced sharpening we suggest David Charlesworth’s DVD Hand Tool Techniques Part 1: Plane Sharpening.

Mouth Adjustment:

To adjust the mouth opening, loosen the two locking screws at the back of the frog; then turn the middle adjuster screw. Observe the opening in front of the blade. When it is correct, set the locking screws again.

Chipbreaker:

Our Chipbreaker is 1/8" thick. The raised lip under the bevel of the chip-breaker is back beveled 1° to ensure that the leading edge contacts the blade firmly. You should never need to dress this surface, but if you do, use a very fine stone and be sure to maintain the angle. The 25° bevel may be honed occasionally. For general work, set the end of the chipbreaker about 1/16" from the cutting edge of the blade; for the finest smoothing work, set it closer to the edge.

Blade Adjustment:

To advance the blade, turn the adjuster nut clockwise. It is always a good idea to finish adjusting the blade by a forward adjustment to take up backlash and to prevent the blade from moving. In order to be able to adjust the blade easily, do not overtighten the lever cap screw.

Tool Care

Materials:

Iron tools are cast from Ductile Iron, a very strong alloy that will take a lot of abuse. These castings are fully stress relieved, a process that removes inherent stresses and ensures that the tool will remain flat and true.

The blade is A-2 cryogenically treated Tool Steel, hardened to Rockwell 60-62 and double tempered. Our heat treating technique ensures that the blade will take and hold a very fine edge for a long time. After heat treating, the blade is fully surface ground on the top, back, and cutting edge, giving a smooth, flat surface that will take a mirror finish very quickly. The thick blade provides solid chatter-free cutting. The cap is Manganese Bronze.

Maintenance:

The soles of Iron planes are surface ground flat and square; the Bronze planes are lapped to a tolerance of .0015". Depending on how much use your tool gets, an occasional light sanding with 320 grit or finer wet/dry paper on a flat surface will keep the sole in as-new condition. Tools with Iron bodies should be kept lightly oiled or waxed to prevent rust. We recommend Jojoba Oil, a vegetable oil based product. It is non-toxic, odor-free and easy to use. Also, in our shop, we use a fine abrasive handblock to remove any light surface oxide from tool bodies and blades. Jojoba Oil and abrasive handblocks are available from us.

A light oiling on the threaded rod, the Brass adjuster nut and the lateral blade adjustment lever will keep them moving freely. Many people like the patina that Bronze gets with age and use, but if you wish to keep the finish bright, a little brass polish is in order. The Cherry knob and handle are finished with wiping varnish and should require no maintenance.

Find everything you need for perfect toolcare.

Guarantee:

Materials and workmanship are guaranteed for the life of your tool. Call for repairs or replacement parts. We are available for advice if you ever have a problem using your tool.

Proposition 65 Notice:

Bronze and brass alloys contain lead, a chemical known to the State of California to cause cancer and birth defects, or other reproductive harm. Wash hands after handling.