No. 610 Low Angle Jack Rabbet Plane Lie-Nielsen Toolworks

No. 610 Low Angle Jack Rabbet Plane

1-610

$245.00



No. 610 Low Angle Jack Rabbet Plane

This plane is a Lie-Nielsen original. It is a combination of our Bench Rabbet Plane (but without the tilting knob and handle) and our Low Angle Jack Plane, giving you a full-width cutting blade in a convenient, low-angle format. Great for raising panels, making long rabbets, working into corners, and large-scale joinery.

  • 12-3/4" long with a full-width, 2.085" wide x .187" thick A2 blade and cross-grain nickers.
  • The blade is bedded 12º.
  • Iron Body, Bronze cap.
  • Weight is 3.65 lbs.

Geometry:

The blade sits in the body at 12°; it comes with a 25° flat ground bevel, making the included cutting angle 37°.

Sharpening:

The blade comes ready to use, but honing a secondary bevel of 5° or 10° will increase performance, help achieve a razor edge quickly, and improve edge life in hardwoods. You can find sharpening instructions in a printable PDF format here:
Sharpening Instructions PDF

For more information on advanced sharpening we recommend David Charlesworth’s video Plane Sharpening, available in both DVD and streaming formats.

Blade Adjustment:

Blade adjustment is simple, direct and positive. Hold the tool in one hand with your thumb on the cap. Loosen the cap thumbscrew all the way, then tighten slightly until there is a little resistance. Adjust depth of cut with the blade adjuster nut. Sight down the base of the tool from the front, and judge depth and squareness of blade by the thin dark line of the blade showing against the sole as it protrudes. When you are done, snug the cap thumbscrew. Do not overtighten.

The blade is about .005" wider than the body. For general purpose work the blade should be just slightly proud of both sides of the tool. When registering into a corner, align the edge of the blade with the side of the body that you want it flush with (laying the tool on its side helps to do this quickly and accurately). To remove the blade, you must lift the back end and tilt it to the side to clear the sidewall of the tool.

This tool is set up to take thin shavings (.008 - .010"). A tool with a large mouth will not perform as well on finish cuts. If you need a heavier cut, the tool can be easily modified by filing a chamfer on the leading edge of the mouth to allow a bigger shaving to pass.

Lateral Adjustment:

The Low Angle Jack Rabbet Plane intentionally has very little lateral adjustment of the blade. This is an advantage. As you adjust the blade, it will track squarely with the sole. The disadvantage is that you must sharpen the blade square. We recommend our Honing Guide to help with this task. If you find that you don’t like this feature, you can grind the blade narrower to give more lateral play.

Nicker:

Nickers cut cross grain fibers first to give a clean shoulder when rabbeting across the grain. The circular A2 nicker is retracted when the flat is at the bottom. Rotate to expose the edge as needed. When fully exposed the nicker protrudes .015". Occasionally, you may need to hone the back (flat) side of the nicker on a fine waterstone to sharpen.

Materials:

The body is cast from Ductile Iron, a very strong alloy that will take a lot of abuse. These castings are fully stress-relieved, a process that removes inherent stresses and ensures that the tool will remain flat and true. The cap is Manganese Bronze. Other parts are Brass, Steel and Cherry.

The blade is 3/16" A2 cryogenically treated Tool Steel, double tempered to Rockwell 60-62. Our heat treating technique ensures that the blade will take and hold a very fine edge for a long time. After heat treating, the blade is fully surface ground on the top, back, and cutting edge, giving a smooth, flat surface that will take a mirror finish very quickly. The thick blade provides solid chatter-free cutting.

Maintenance:

The body casting is ground flat and square to a tolerance of .0015". Depending on how much use your tool gets, an occasional light sanding with 320 grit or finer wet/dry paper on a flat surface will keep the sole in as-new condition. Tools with Iron bodies should be kept lightly oiled or waxed to prevent rust. We recommend Jojoba Oil, a plant based oil product that is non-toxic, odor-free and easy to use. Also, in our shop, we use a fine abrasive handblock to remove any light surface oxide from tool bodies and blades. Jojoba Oil and abrasive handblocks are available from us.

A light oiling on the threaded rod, the Brass adjuster nut and the lateral blade adjustment lever will keep them moving freely. Many people like the patina that Bronze gets with age and use, but if you wish to keep the finish bright, a little brass polish is in order. The Cherry knob and handle are oiled and buffed with wax to produce a natural finish. Wipe with oil as desired to refresh.

Find everything you need for tool care.

Guarantee:

Materials and workmanship are guaranteed for the life of your tool. Call for repairs or replacement parts. We are available for advice if you ever have a problem using your tool.

Proposition 65 Notice:

Bronze and brass alloys contain lead, a chemical known to the State of California to cause cancer and birth defects, or other reproductive harm. Wash hands after handling.